ejecting

英 [iˈdʒektɪŋ]

美 [iˈdʒektɪŋ]

v.  驱逐; 逐出; 赶出; 喷出; 喷射; 排出; (飞行员在飞机坠毁前从弹射座椅)弹出
eject的现在分词

柯林斯词典

• VERB 驱逐;把…逐出
  If youejectsomeonefroma place, you force them to leave.
  1. Officials used guard dogs to eject the protesters...
     官员们用警犬驱散抗议人群。
  2. He was ejected from a restaurant.
     他被逐出餐厅。
• VERB 弹出;喷出;射出
  Toejectsomething means to remove it or push it out forcefully.
  1. He aimed his rifle, fired a single shot, then ejected the spent cartridge.
     他用步枪瞄准，射出一枚子弹，然后退出空弹壳。
• VERB （通常指飞行员从即将坠毁的飞机中）弹射出来
  When a pilotejects froman aircraft, he or she leaves the aircraft quickly using an ejector seat, usually because the plane is about to crash.
  1. The pilot ejected from the plane and escaped injury.
     飞行员从飞机中弹出，安然无恙。

双语例句

• Excitation radiation may do this by penetrating to the cathode and ejecting a photoelectron. Some of the excited atoms undergo radiative deexcitation.
  激发辐射可能射到阴极，逐出一个光电子，从而引起这个。某些受激的原子会发生辐射性退激。
• Ejecting and heating performance of the heater at low steam pressure was studied through the experimental method.
  用试验方法研究了该加热器在低进汽压力下的引射性能和加热性能。
• Type of radioactive disintegration ( see radioactivity) in which some unstable atomic nuclei dissipate excess energy by spontaneously ejecting an alpha particle.
  放射性蜕变的一类，某些不稳定原子核自发射出一个α粒子以耗散过剩能量。
• DESIGN INJECTION MOULD WITH QUADRATIC EJECTING MECHANISM OF SLIDER AND WEDGE DUAL PUSH PLATE The friction is modeled with a modified coulomb friction model.
  滑块斜楔双推板式二次推出机构注塑模的设计模具与板料的接触摩擦采用一个修正的库仑摩擦模型。
• The Study and Calculation of Gas Filling and Ejecting Characteristics of Gas-propelled APDS
  气推式脱壳弹充排气规律研究与计算
• Design injection mould with quadratic ejecting mechanism of slider and wedge dual push plate
  推床的导板（或推板）滑块斜楔双推板式二次推出机构注塑模的设计
• A new ejecting removal mechanism of particles is presented based on particle elastic deformation to overcome the flaws of rolling removal mechanism in laser-induced plasma shock wave cleaning.
  针对激光等离子体冲击波清洗颗粒技术中的滚动移除机制缺陷，提出一种基于颗粒弹性形变的弹出移除模型。
• Each front bracket convex plate is provided with at least two guiding slopes which are in different radians and can be butted with the pushed part of the ejecting unit.
  每个前托凸板都具有至少两个弧度不同并可靠抵在通出单元的受推部上的导引斜面。
• Finally, the location and size of the ejector pins that correspond to the discrete ejecting forces are obtained.
  最后，这个位置和大小的异形销，迎合了离散排出力量。
• The design of side core-pulling framework and ejecting framework is difficult in designing injection mould.
  侧面抽芯机构和顶件机构的设计是注射模具设计的难点。